JUST HOW TO SET UP A BATH TUB

Just How to Set up a Bath Tub

Just How to Set up a Bath Tub

Blog Article

Schedule Now!

Just how do you really feel on the subject of How to Install a Bathtub Yourself?


How to Install a Bathtub Yourself
Setting up a bathtub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a new one is likewise a reasonably challenging project. If the old bathtub is conveniently available, the project can move easily; if you need to open a wall surface to eliminate the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will require a helper to move out the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task and also are comfortable trying it. As opposed to hiring a professional to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently bought a new tub and do not require to transform the plan of your previous water system pipelines.
Your devices as well as product list should make up the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installation


    Firstly, the sustaining frame supplied with the bath should be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent strain on the bath tub.
    Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
    Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final placement.

    Removing Old Taps


    If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be quite bothersome due to the limited gain access to that is typically the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
    Prior to proceeding to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.

    Setting up the Tub


    Utilizing both wooden boards under its feet, put the tub in the needed setting. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
    The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the level as well as readjusting the feet on the tub until the spirit level reviews degree.
    To mount taps, fit the bottom of the outermost adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the various other tap.
    Activate the water as well as check all joints and also new pipework for leaks and tighten them if essential. Load the bath tub and also inspect the overflow outlet and the regular electrical outlet for leaks.
    Ultimately, repair the bath paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bath tub ought to wait till the bath tub has been utilized at least once as this will resolve it into its last setting.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the tap and the other end gives a connection to the existing supply pipelines.
    If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next, position the tap in the mounting hole in the bath/basin making certain that the washing machines are in location between the faucet and the sink. Safeguard the faucet in position with the supplier offered backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former type ought to be connected to the tap finishes first, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, bring about issues with dampness as well as possible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealants to assimilate your components and also installations. They are sold in tubes as well as cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to enable the motion experienced when the bathtub is in use. The sealant can split relatively very early if you do not take into account this movement before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    Do you enjoy reading about Tools You Need to Install a New Bathtub ? Put feedback below. We'd be glad to find out your ideas about this post. We are looking forward that you visit us again before long. Do you know about somebody else who is truly interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Take a moment to share it. Thank you so much for your time spent reading it.




    Visit Page


    Report this page